
Selective Pallet Racking
Selective pallet racking fitted with wire decking across each level.

Cantilever rack in St. Petersburg supports fabrication stock and long profiles without making a working wall the storage system. Uprights carry projecting arms behind the material, leaving no front columns across the retrieval face. Loads can extend along several support positions, but each product needs adequate bearing throughout its length. That includes the short lengths returned after cutting, not only the full bundles delivered to receiving.
Gateway / Carillon and the 28th Street industrial corridor bring electronics, light manufacturing, and regional distribution into constrained building footprints. Cantilever racking should be drawn alongside the production route rather than fitted into whatever corner remains. Selective pallet rack can handle boxed components and palletized output nearby, while the long-material row provides access suited to profiles, tube, and bar stock.
For single-sided storage, we look for an edge position that leaves a clear working face toward the material route. Double-sided storage can place different product groups on opposite faces, provided both approaches stay available. Indoor and outdoor arrangements need separate exposure and structural checks. Surface-sensitive profiles and sheet packs may be better assigned indoors, while any outdoor specification must reflect its actual location and stored products. The cantilever rack plan should retain a clear transfer connection between profile storage and fabrication.
Installation is carried out by experienced crews we schedule and manage. The agreed scope establishes base locations, upright alignment, bracing, and arm elevations against the reviewed plan. Capacity information should remain tied to that configuration after handover. Before moving arms or changing a level from light profiles to heavy bar, have the revised arrangement checked rather than assuming the unchanged upright can accept it.
St. Petersburg warehouse racking · Long-load support options · FIFO pallet storage in St. Petersburg · Bulk pallet lanes in St. Petersburg
Check access at the busiest transfer point before deciding the final row position. Floor area occupied by a base is only part of the space needed to retrieve long material.
Record profile lengths, pack depths, and the heaviest bundle in each group. Identify short cut pieces and sheet packs that cannot share the same unsupported spans.
Place uprights so every assigned product has the required support. Specify decking or product-contact surfaces where narrow arms alone do not provide the needed bearing.
Choose arm projections and capacities together, then check total column loading. Confirm base selection and bracing for the actual number of faces and planned level arrangement.
Use the forklift dimensions with the longest bundle aboard. Compare a side-loader arrangement where applicable, accounting for transfer clearance rather than assuming a smaller aisle will work.
Raising another level does not solve a bearing problem at the levels below. We first check upright spacing against the material stiffness, minimum load length, and intended end overhang. Pipe and thin tube can behave differently from solid bar; lumber and sheet inventory may need additional supports or a specified deck. The design needs to remain suitable after a partial withdrawal changes how much material rests on each arm.
Arm length is selected for the depth projecting out from the column. Its rating depends on the stated loading position, so a heavier pack cannot simply be shifted outward to make room behind it. Combined arm loads must stay within the upright and base specification. We also allow vertical clearance for bundle height, fork placement, and the lifting movement needed to pass any retaining feature.
Tampa Pallet Racks, a division of Warehouse Equipment & Supplies Co., has supplied and installed storage systems since 1997. We use the load review to connect the component list with a drawing that shows where the material sits and how operators reach it.


Include assembly benches, carts, and outbound pallet staging in the drawing. Their relationship to the rack determines whether the long-load approach remains available during normal production.
A look at recent pallet rack installations across the Tampa Bay area.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

Pallet racking set up with carton flow roller lanes on the lower levels.

Drive-in pallet racking built with deep bays that store pallets several positions deep.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking installed across a warehouse.

Selective pallet racking fitted with wire decking.

Selective pallet racking in a warehouse.

Push back pallet racking with nested carts that store pallets several deep from one aisle.

Selective pallet racking set up along a warehouse wall.
Contact (813) 723-3771 to discuss stock dimensions, available height, and the equipment moving material between storage and production. Call (813) 723-3771.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
(813) 723-3771Monday - Friday: 7:00 AM - 7:00 PM

Every pallet reachable, every time. The baseline we size everything else against.
View details
Two to six pallets deep from one aisle, without giving up much reach.
View details
Load one side, pick the other, and let gravity enforce first in, first out.
View details
Forklifts enter storage lanes, reducing aisle space for large quantities of the same SKU.
View details
Cases advance to the picker instead of the picker hunting for cases.
View detailsOur delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.
Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
Monday - Friday: 7:00 AM - 7:00 PM
Saturday: Closed
Sunday: Closed
Call (813) 723-3771 or request a quote and we will get a layout started.