Serving the Tampa Bay Area
    Cantilever Rack warehouse storage system
    Wesley Chapel, Florida

    Cantilever Rack in Wesley Chapel, FL

    Cantilever rack gives Wesley Chapel commercial suppliers a defined home for long contractor materials that otherwise occupy receiving and assembly space. Arms project from structural uprights, creating storage levels with no front columns across the loading opening. Pipe, tube, bar and lumber can span several arms while remaining available from the working face.

    Service distribution and light assembly around the SR-56 corridor and Cypress Creek often share floor area with dispatch preparation. Sheet products and long supply bundles should have specified bearing locations, not improvised positions beside a workbench. Plan those positions around both incoming bundles and the smaller quantities leaving for jobs.

    (813) 723-3771

    Choose cantilever racking for contractor lengths

    Selective pallet storage handles packaged fittings and palletized supplies with direct access to each position. Cantilever racking instead supports lengthy material across arms without a front frame dividing its loading face. A mixed arrangement can separate these handling tasks while preserving the access each inventory group needs.

    Tampa Pallet Racks, a division within Warehouse Equipment & Supplies Co., brings the company’s supplying and installing background since 1997 to the proposal. Component counts are developed from product dimensions and storage assignments, with the load assumptions visible for the buyer to review.

    Free warehouse consultation
    CAD layout with position counts
    Installation by trusted installation partners
    Cantilever warehouse racking holding steel tubing
    Cantilever rack storing lumber and wood products

    Separate assembly from material retrieval

    As service inventory grows, reserve an unloading position that does not block long-stock retrieval. Keep job-order checking and assembly carts outside the turning envelope, so an occupied work area does not make a correctly sized storage level inaccessible.

    service distribution
    commercial supply
    and light assembly

    Plan the cantilever storage rack assembly

    Choose single-sided perimeter storage where only one retrieval face is practical. Double-sided islands need accessible aisles on both sides plus room for bases and loaded arms. For round pipe, specify suitable containment such as stops or inclined arms; for sheet goods, consider approved support surfaces rather than assuming every product can bridge bare arms.

    Indoor use calls for clear-height and overhead-obstruction checks; outdoor placement adds exposure and finish considerations to the structural specification. We arrange installation with experienced crews that are scheduled and managed around the agreed work sequence. Assembly includes the specified bases and anchoring, aligned uprights, bracing and arm positions documented for the proposed loads.

    Wesley Chapel warehouse racking · Long-load support options · FIFO pallet storage in Wesley Chapel · Bulk pallet lanes in Wesley Chapel

    Commercial pipe and tube separated by job length
    Assembly bar stock with identified bearing requirements
    Lumber and sheet packs outside the workbench zone
    Call (813) 723-3771

    Cantilever rack checks for compact buildings

    In a compact supply building, the bases and truck movements matter as much as the upright height.

    1

    Establish arm projection

    Measure the stored bundle depth rather than relying on nominal product dimensions. Arm length needs to match the specified bearing area without allowing unsupported front projection. Sheet bundles can demand a broader support arrangement than narrow packs of bar or conduit.

    2

    Connect arm ratings to columns

    Arm capacity is tied to its length and stated load distribution. Check the heaviest package against each bearing point, then total the loads assigned to the upright. Neither another arm nor another level increases the capacity of the existing base and column assembly by itself.

    3

    Locate supports for the full range

    Support spacing reflects stiffness and the manufacturer’s loading requirements, not merely the longest stock length. Check short contractor cuts as well as full bundles. Flexible lumber, thin tube and sheet material may need closer supports to control sag and maintain appropriate end overhang.

    4

    Test access before adding levels

    Allow room to insert forks and lift the load clear of its arms. A conventional forklift needs turning clearance for projecting material; a side-loader follows a different approach. Both require checks against truck ratings at the actual load center and intended lifting height.

    Recent Pallet Rack Projects

    A look at recent pallet rack installations across the Tampa Bay area.

    Selective pallet racking with wire decking in a warehouse

    Selective Pallet Racking

    Selective pallet racking fitted with wire decking across each level.

    Selective pallet racking with wire decking under a wood-truss roof

    Selective Racking with Wire Decking

    Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

    Carton flow racking with roller lanes

    Carton Flow Racking

    Pallet racking set up with carton flow roller lanes on the lower levels.

    Drive-in pallet racking with deep storage bays

    Drive-In Pallet Racking

    Drive-in pallet racking built with deep bays that store pallets several positions deep.

    Selective pallet racking with wire decking

    Selective Pallet Racking with Wire Decking

    Selective pallet racking fitted with wire decking across each level.

    Selective pallet racking in a warehouse

    Selective Pallet Racking

    Selective pallet racking installed across a warehouse.

    Selective pallet racking with wire decking

    Selective Pallet Racking

    Selective pallet racking fitted with wire decking.

    Selective pallet racking in a warehouse

    Selective Pallet Racking

    Selective pallet racking in a warehouse.

    Push back pallet racking with nested carts

    Push Back Pallet Racking

    Push back pallet racking with nested carts that store pallets several deep from one aisle.

    Selective pallet racking along a warehouse wall

    Selective Pallet Racking

    Selective pallet racking set up along a warehouse wall.

    Cantilever rack: turn the load list into a quote

    Share load lengths, heaviest weights, clear height and a building plan for your free CAD layout and itemized quote. Phone (813) 723-3771 to review the material mix. Call (813) 723-3771.

    Tampa Pallet Racks

    7402 N 56th St.

    Ste 355-580

    Tampa, FL 33617

    (813) 723-3771

    Monday - Friday: 7:00 AM - 7:00 PM

    We respect your privacy. Your information will never be shared.

    Commercial-supply purchasing answers

    Nearby Areas We Also Serve

    Our delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.

    Where We Work

    Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.

    Tampa Pallet Racks

    Address

    7402 N 56th St.
    Ste 355-580
    Tampa, FL 33617

    Business Hours

    Monday - Friday: 7:00 AM - 7:00 PM
    Saturday: Closed
    Sunday: Closed

    Need Cantilever Rack in Wesley Chapel?

    Call (813) 723-3771 or request a quote and we will get a layout started.

    (813) 723-3771
    Call Now