Serving the Tampa Bay Area
    Cantilever Rack warehouse storage system
    Lakeland, Florida

    Cantilever Rack in Lakeland, FL

    Cantilever rack helps Lakeland manufacturers organize long production material by length and section instead of stacking bundles across working floor. Arms extend from braced uprights without front columns interrupting the retrieval face. That open frontage accommodates bar, pipe, tube and lumber whose lengths do not fit conventional pallet positions.

    County Line Road distribution activity and manufacturing around Lakeland Airside Center create different handling patterns. A reserve bundle arriving by forklift may later feed smaller production picks. The storage plan needs to support both the full incoming load and the remaining stock after material has been removed.

    (813) 723-3771

    Cantilever rack geometry for changing bundles

    Production storage should remain workable as bundles shrink and stock lengths change during a shift.

    1

    Identify the bearing width

    Choose arm length from the actual front-to-back depth of stored material. A wide lumber pack and a narrow steel bundle can share a length but require different arm projections. Check clearance behind the load without treating the upright as a bearing surface.

    2

    Evaluate the loaded assembly

    The heaviest weight establishes only part of the specification. Each arm needs adequate capacity for its share and load position, while the upright, base and bracing must suit the cumulative loading. Adding levels changes that calculation even when individual bundles remain unchanged.

    3

    Check sag between uprights

    Support spacing must accommodate stiffness, bundle integrity and permitted end overhang. Thin tube or sheet material can need closer bearing points than solid bar. Confirm the shortest production remainder can still rest on the required supports rather than balancing between intended storage locations.

    4

    Provide withdrawal space

    Set elevations to allow forks beneath the bundle and sufficient lift above arm tips. A side-loader may handle long pieces parallel to its travel direction; a counterbalance forklift needs turning room for the load ends. Compare those movements on the drawing before fixing aisle widths.

    Specify a cantilever storage rack by load

    A single-sided perimeter run keeps retrieval on one face, while a double-sided island presents separate faces to adjacent aisles. Calculate the base projection and loaded depth on each side, not just column thickness. Separate levels or locations for sheet goods may need approved decking or other load-spreading accessories.

    Outdoor storage requires a finish and structural arrangement selected for the exposure; indoor positioning requires attention to overhead obstructions and available clear height. Stops for round stock must suit the material without obstructing forks. We schedule and manage experienced installation crews, with assembly sequencing, upright alignment, bracing and final arm elevations tied to the accepted plan.

    Lakeland warehouse racking · Long-load support options · FIFO pallet storage in Lakeland · Bulk pallet lanes in Lakeland

    Manufacturing bar stock indexed by section and length
    Tube bundles withdrawn by side-loader
    Lumber or sheet reserves with defined support requirements
    Call (813) 723-3771

    Where cantilever racking fits production

    Start by separating pallet loads from unsupported long products. Selective storage offers direct pallet access for packaged components; cantilever racking presents horizontal material across several arms. Neither format replaces the other when a facility carries both finished goods and lengthy raw stock.

    As the storage division of Warehouse Equipment & Supplies Co., Tampa Pallet Racks draws on a supplying and installing history dating to 1997. Our proposal identifies the arm arrangement and structural components so buyers can compare equivalent support conditions rather than nominal row lengths.

    Free warehouse consultation
    CAD layout with position counts
    Installation by trusted installation partners
    Cantilever warehouse racking holding steel tubing
    Cantilever rack storing lumber and wood products

    Keep receiving separate from machine feed

    Production supply and regional logistics do not always peak together. Keep the material receiving position distinct from the machine-feed route, and allow a place to check bundle labels before the truck approaches the assigned arms.

    regional logistics
    food distribution
    and manufacturing

    Recent Pallet Rack Projects

    A look at recent pallet rack installations across the Tampa Bay area.

    Selective pallet racking with wire decking in a warehouse

    Selective Pallet Racking

    Selective pallet racking fitted with wire decking across each level.

    Selective pallet racking with wire decking under a wood-truss roof

    Selective Racking with Wire Decking

    Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

    Carton flow racking with roller lanes

    Carton Flow Racking

    Pallet racking set up with carton flow roller lanes on the lower levels.

    Drive-in pallet racking with deep storage bays

    Drive-In Pallet Racking

    Drive-in pallet racking built with deep bays that store pallets several positions deep.

    Selective pallet racking with wire decking

    Selective Pallet Racking with Wire Decking

    Selective pallet racking fitted with wire decking across each level.

    Selective pallet racking in a warehouse

    Selective Pallet Racking

    Selective pallet racking installed across a warehouse.

    Selective pallet racking with wire decking

    Selective Pallet Racking

    Selective pallet racking fitted with wire decking.

    Selective pallet racking in a warehouse

    Selective Pallet Racking

    Selective pallet racking in a warehouse.

    Push back pallet racking with nested carts

    Push Back Pallet Racking

    Push back pallet racking with nested carts that store pallets several deep from one aisle.

    Selective pallet racking along a warehouse wall

    Selective Pallet Racking

    Selective pallet racking set up along a warehouse wall.

    Cantilever rack: build a comparable material quote

    Request a free CAD layout and itemized quote using your load lengths, heaviest weights, clear height and building plan. Discuss production access at (813) 723-3771. Call (813) 723-3771.

    Tampa Pallet Racks

    7402 N 56th St.

    Ste 355-580

    Tampa, FL 33617

    (813) 723-3771

    Monday - Friday: 7:00 AM - 7:00 PM

    We respect your privacy. Your information will never be shared.

    Production-stock buying questions

    Nearby Areas We Also Serve

    Our delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.

    Where We Work

    Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.

    Tampa Pallet Racks

    Address

    7402 N 56th St.
    Ste 355-580
    Tampa, FL 33617

    Business Hours

    Monday - Friday: 7:00 AM - 7:00 PM
    Saturday: Closed
    Sunday: Closed

    Need Cantilever Rack in Lakeland?

    Call (813) 723-3771 or request a quote and we will get a layout started.

    (813) 723-3771
    Call Now