Serving the Tampa Bay Area
    Pushback Rack warehouse storage system
    Oldsmar, Florida

    Pushback Rack in Oldsmar, FL

    Pushback rack in Oldsmar gives mid-sized buildings a way to store repeat pallets deeper without spreading across more floor. Each lane carries nested carts on inclined rails, holding two to six pallets that you reach from one aisle.

    Many North Pinellas shops near Tampa Road and Race Track Road were built long ago, with tighter column spacing and modest footprints. A layout that removes a few aisles helps there, provided the lanes fit around the columns.

    (813) 723-3771

    Why a pushback pallet rack layout fits older Oldsmar bays

    Older, smaller buildings rarely allow an ideal grid. Columns land where they land, and every aisle you remove is floor you can reuse for production supplies or staging.

    As a division of Warehouse Equipment & Supplies Co., Tampa Pallet Racks draws on a business supplying and installing since 1997. Our proposals cover new rack for electronics, fabrication and regional distribution operations.

    Because lane widths follow the pallet and the column grid, we draw bay by bay. If a lane will not fit between columns, the drawing says so before anything is ordered.

    Free warehouse consultation
    CAD layout with position counts
    Installation by trusted installation partners
    High-density pushback rack lanes loaded with pallets
    Pushback pallet racking showing cart rails and load beams

    Oldsmar, between two counties

    Tampa Road and Race Track Road link Oldsmar buildings to Pinellas and Hillsborough delivery markets. Tight lots and older structures make floor space the scarce resource, so deeper lanes pay off fastest here. Keep the turning approach open where incoming pallets meet the production supply route.

    electronics
    fabrication
    and regional distribution

    Fitting push back racking to columns and pallets

    We compare pushback with selective and drive-in on your floor plan. Selective keeps full access, drive-in goes deepest, and pushback usually lands between the two for lane-level access without truck entry. Pushback rack leaves the driver outside the storage block, unlike drive-in. That distinction matters when fabrication traffic passes the same aisle and entering a long lane would hold up other movements. FIFO components need another storage method that can expose the earlier pallet directly.

    Lane depth versus pallets per SKU decides the result. Component pallets that arrive in pairs call for shallow lanes, while bulk inputs repeated many times justify more depth. Review both average and peak counts. If a component reaches six pallets only occasionally, two shallower lanes may serve the normal inventory better than one long lane. Allow for the number of separate parts competing for those faces.

    Adding to a system later works best when frames, beams and rails match. We keep a component list from the first installation so later bays tie in without surprises. Installation crews are scheduled and managed with production access in mind. Verify the frame rating at the actual beam spacing, not just at the original installation height. Moving levels farther apart can reduce the allowable upright load even when the beams themselves remain unchanged.

    Oldsmar warehouse racking · Pushback system options · FIFO lanes in Oldsmar · Deep reserve storage in Oldsmar

    Electronics assemblers holding repeat reserve pallets
    Fabrication shops short on floor between columns
    Regional distributors in compact older buildings
    Call (813) 723-3771

    Inside an Oldsmar pushback rack lane

    A lane is a few components working together, and each has a job. Push back racking depends on consistent pallet support. Record pallet dimensions, underside construction, overhang and the heaviest load before selecting the cart assembly. A pallet that bridges incorrectly can interrupt movement even when its weight is below the stated capacity.

    1

    Nested carts

    Carts are shaped to slide under one another, letting pallets stack back along the rail without forklifts leaving the aisle.

    2

    Inclined rails

    The slope is what returns each pallet to the front after the one ahead is removed.

    3

    Frames and beams

    Upright frames carry the load. Each level uses a beam pair, and the spacing between levels sets pallet height.

    4

    Newest pallet first

    Retrieval follows last in, first out, so lots with strict order of use stay elsewhere.

    Recent Pallet Rack Projects

    A look at recent pallet rack installations across the Tampa Bay area.

    Selective pallet racking with wire decking in a warehouse

    Selective Pallet Racking

    Selective pallet racking fitted with wire decking across each level.

    Selective pallet racking with wire decking under a wood-truss roof

    Selective Racking with Wire Decking

    Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

    Carton flow racking with roller lanes

    Carton Flow Racking

    Pallet racking set up with carton flow roller lanes on the lower levels.

    Drive-in pallet racking with deep storage bays

    Drive-In Pallet Racking

    Drive-in pallet racking built with deep bays that store pallets several positions deep.

    Selective pallet racking with wire decking

    Selective Pallet Racking with Wire Decking

    Selective pallet racking fitted with wire decking across each level.

    Selective pallet racking in a warehouse

    Selective Pallet Racking

    Selective pallet racking installed across a warehouse.

    Selective pallet racking with wire decking

    Selective Pallet Racking

    Selective pallet racking fitted with wire decking.

    Selective pallet racking in a warehouse

    Selective Pallet Racking

    Selective pallet racking in a warehouse.

    Push back pallet racking with nested carts

    Push Back Pallet Racking

    Push back pallet racking with nested carts that store pallets several deep from one aisle.

    Selective pallet racking along a warehouse wall

    Selective Pallet Racking

    Selective pallet racking set up along a warehouse wall.

    Plan storage between Oldsmar columns

    Supply the column grid, loaded pallet sizes and component identification for a free CAD plan plus an itemized quotation. Call (813) 723-3771.

    Tampa Pallet Racks

    7402 N 56th St.

    Ste 355-580

    Tampa, FL 33617

    (813) 723-3771

    Monday - Friday: 7:00 AM - 7:00 PM

    We respect your privacy. Your information will never be shared.

    Common questions from Oldsmar operators

    Nearby Areas We Also Serve

    Our delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.

    Where We Work

    Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.

    Tampa Pallet Racks

    Address

    7402 N 56th St.
    Ste 355-580
    Tampa, FL 33617

    Business Hours

    Monday - Friday: 7:00 AM - 7:00 PM
    Saturday: Closed
    Sunday: Closed

    Need Pushback Rack in Oldsmar?

    Call (813) 723-3771 or request a quote and we will get a layout started.

    (813) 723-3771
    Call Now