
Selective Pallet Racking
Selective pallet racking fitted with wire decking across each level.

Carton flow rack in Oldsmar can organize electronics assembly supplies into rear-loaded lanes that present cases and totes at the production picking edge. Inclined rollers move each compatible container forward under gravity. That gives the material handler a consistent withdrawal position without requiring assembly staff to reach through a partially emptied storage shelf.
The starting point is the assembly supply unit: a sealed component carton, a rigid tote, or an approved container carrying packaged subassemblies. We do not assume loose sensitive components belong directly on rollers. Your packaging and handling requirements determine what may enter the lane and how the operator should remove or open it.
A pallet bay retrofit requires more than matching the outside width of a flow bed. Support details, structural loading, level spacing, and container removal clearance all influence the arrangement. If pallet reserve stays above the pick module, its handling path should not conflict with staff issuing components below.
We show proposed lane widths, roller levels, module frontage, and rear loading access on the layout. Installation is carried out by experienced crews that we schedule and manage. The setup sequence includes checking representative loaded containers for straight travel and suitable containment before routine material issue starts.
Oldsmar warehouse racking · Case and tote picking options · FIFO pallet reserve in Oldsmar · LIFO reserve lanes in Oldsmar
Treat roller travel as one part of the assembly supply process. The following checks connect lane geometry with the people loading, selecting, and recording material at either end.
Measure the widest loaded tote, its base contact surfaces, and the range of operating weights. Roller support should suit that base rather than relying on a nominal bin size that ignores projecting lids or handles.
Set dividers so containers remain aligned as they descend. Lane identification should distinguish related components and revisions where necessary, with enough label visibility at the loading end for a replenisher to confirm placement before release.
The incline carries the next container forward after the preceding one is withdrawn. Trials should include partly filled totes because their travel may differ from full containers, especially when the contents are concentrated at one end.
A rear loading route allows material handlers to add approved stock without taking over the front working position. Preserve FIFO by placing new containers behind the established queue rather than adding them wherever an opening appears.
A production pick module should reflect the sequence in which materials are issued, not simply alphabetical part order. Related component families can occupy neighboring faces while dividers keep similar containers separated. A line needing several small inputs may benefit more from extra distinct lanes than from long channels holding excess material.
Supplying and installing storage equipment since 1997 is the background of Warehouse Equipment & Supplies Co., the company whose division is Tampa Pallet Racks. We apply that experience by examining the container path from incoming material to assembly issue before specifying the storage arrangement.
With carton flow racking, FIFO describes the physical withdrawal sequence when later receipts are introduced at the back. It does not replace lot verification, material release status, or your handling controls. Keep each lane assignment clear so an incoming component revision does not mingle unnoticed with an earlier approved version.


Oldsmar electronics and fabrication operations connected by Tampa Road and Race Track Road need material staging that supports production rather than surrounding it. A case flow rack bank can serve as a defined issue boundary between reserve and assembly. Its position should preserve room for material handling while keeping approved components accessible to the people building the next batch.
A look at recent pallet rack installations across the Tampa Bay area.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

Pallet racking set up with carton flow roller lanes on the lower levels.

Drive-in pallet racking built with deep bays that store pallets several positions deep.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking installed across a warehouse.

Selective pallet racking fitted with wire decking.

Selective pallet racking in a warehouse.

Push back pallet racking with nested carts that store pallets several deep from one aisle.

Selective pallet racking set up along a warehouse wall.
Tell us how containers are released to production and returned to reserve. We can discuss roller support, separation of component families, and lane quantities that suit the assembly schedule. Call (813) 723-3771.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
(813) 723-3771Monday - Friday: 7:00 AM - 7:00 PM

Every pallet reachable, every time. The baseline we size everything else against.
View details
Two to six pallets deep from one aisle, without giving up much reach.
View details
Load one side, pick the other, and let gravity enforce first in, first out.
View details
Forklifts enter storage lanes, reducing aisle space for large quantities of the same SKU.
View details
Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.
View detailsOur delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.
Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
Monday - Friday: 7:00 AM - 7:00 PM
Saturday: Closed
Sunday: Closed
Call (813) 723-3771 or request a quote and we will get a layout started.