
Selective Pallet Racking
Selective pallet racking fitted with wire decking across each level.

Pushback rack in Clearwater helps a building that stores the same part by the pallet and cannot keep adding floor rows. Pallets roll on nested carts down inclined rails, and a lane can hold two to six of them while the operator works from one aisle.
Between US-19, Ulmerton Road, Roosevelt Boulevard and the St. Pete-Clearwater Airport area, many Pinellas suppliers feed electronics and aerospace assembly lines from medium-sized buildings. Reserve inventory there tends to be repetitive, which is the pattern lanes handle best.
Start with a count: how many pallets of each part sit in reserve during a normal week and during the busiest one. A four-deep lane for an item that rarely exceeds two pallets is wasted rail. Keep FIFO parts in an arrangement that presents earlier receipts without clearing newer ones.
Then check the frame. Capacity is tied to how far apart the beam levels sit and how much load rides on each pair, so we fix those figures before any quantity is quoted. Do not assume a stronger beam makes the upright stronger. Frame ratings depend on vertical beam spacing, and every level adds to the load carried by that frame.
Planning to extend the system later? Frames, beams and carts need to line up with the original rack, so we document the components and design the first phase with expansion in mind. Installation crews are scheduled and managed around the agreed scope of work. A matching connector shape is not enough: verify load ratings, rail supports, cart travel and pallet clearance before attaching new equipment to an existing bay.
Clearwater warehouse racking · Pushback system options · FIFO lanes in Clearwater · Deep reserve storage in Clearwater
Think of each lane as a shallow ramp with a train of carts on it. Push back racking lets neighboring lanes hold different parts, but combining unrelated parts within one lane creates retrieval problems. Give each recurring item its own accessible face.
Forklifts load and retrieve at the front. No second aisle is needed behind the rack.
Empty carts occupy a nested position at the face. Successive loads move them rearward into separate supported positions along the rail set.
The selected beam arrangement supports the rail assembly at each storage level. Capacity is checked per pair, per level, together with the complete frame loading.
The newest pallet in is the first out of that lane. Parts with a steady turn tolerate it comfortably.
Parts operations rarely lack pallets. They lack aisles. Drive-in rack removes more aisles but puts forklifts inside the structure, while selective rack keeps access and spends the floor. Pushback sits between them.
Tampa Pallet Racks operates as a division of Warehouse Equipment & Supplies Co., supplying and installing since 1997. We provide new rack for parts storage and coordinate the work around the equipment and inventory sharing your building.
Our drawing shows pushback beside a selective plan of your same footprint. You see the added pallet positions and the pick faces you lose, then decide with both on paper.


Buildings around US-19, NE Coachman and the airport district often combine assembly, parts storage and shipping under one roof. Lanes let the reserve shrink into fewer aisles so assembly and dispatch keep their room. In Gateway and Mid-Pinellas facilities, check the route from receiving to each lane face as carefully as the storage block itself. A dense block should not send replenishment trucks across the active assembly supply path.
A look at recent pallet rack installations across the Tampa Bay area.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

Pallet racking set up with carton flow roller lanes on the lower levels.

Drive-in pallet racking built with deep bays that store pallets several positions deep.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking installed across a warehouse.

Selective pallet racking fitted with wire decking.

Selective pallet racking in a warehouse.

Push back pallet racking with nested carts that store pallets several deep from one aisle.

Selective pallet racking set up along a warehouse wall.
Provide component pallet dimensions and the assembly floor plan to receive a free CAD proposal with itemized equipment and installation pricing. Call (813) 723-3771.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
(813) 723-3771Monday - Friday: 7:00 AM - 7:00 PM

Every pallet reachable, every time. The baseline we size everything else against.
View details
Load one side, pick the other, and let gravity enforce first in, first out.
View details
Forklifts enter storage lanes, reducing aisle space for large quantities of the same SKU.
View details
Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.
View details
Cases advance to the picker instead of the picker hunting for cases.
View detailsOur delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.
Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
Monday - Friday: 7:00 AM - 7:00 PM
Saturday: Closed
Sunday: Closed
Call (813) 723-3771 or request a quote and we will get a layout started.