
Selective Pallet Racking
Selective pallet racking fitted with wire decking across each level.

Cantilever rack in Bradenton puts lumber and long building products on projecting arms so pickup preparation does not depend on dismantling floor stacks. Uprights stand behind the material, with no front columns dividing the loading face. A bundle can span several supports while a forklift approaches its lifting position. The design starts with the material, including short remnants that must remain supported after full lengths leave.
Along the 15th Street East corridor, building-material supply and commercial distribution can involve both long stock and palletized orders. Around Ellenton, the same planning question is how to separate bundle retrieval from outbound staging. Cantilever racking belongs in the long-load zone; selective pallet rack can retain bagged products, cartons, and other pallet-supported inventory.
Arm length follows the depth of the stored bundle, not its overall length along the row. Excessive projection into the aisle wastes maneuvering room, while insufficient bearing leaves material unsupported. Arm capacity must cover the actual reaction at each support; dividing a bundle weight evenly is not enough when packs are uneven or different lengths share a level. Upright and base ratings also constrain the complete arrangement.
Support spacing needs particular attention for flexible trim, pipe, tube, and sheet goods alongside lumber. Bar stock may be stiff yet carry substantial weight in a narrow contact area. We compare the shortest pack with the longest bundle and check end overhang, bending between supports, and any need for decking. A cantilever storage rack should hold each intended load without relying on neighboring bundles to keep it stable.
Tampa Pallet Racks is a division of Warehouse Equipment & Supplies Co., supplying and installing storage systems since 1997. For this project, that background supports a practical review of arm selection, upright configuration, and handling routes before the equipment list is settled.


Mark receiving and pickup boundaries on the building plan so long stock can leave its arms without crossing an occupied order-assembly position.
Work through the support arrangement before assigning storage levels. The loading method and the material remaining after a partial pick matter as much as the incoming pack.
Record bundle width across the arms and the fork entry arrangement. Choose arm projection that supports the load while leaving room for a controlled setdown and withdrawal.
Set column centers against material stiffness and the shortest stored lengths. Check that both ends remain supported through partial withdrawals rather than copying the spacing of a different product.
Match each arm rating to its loading condition, then check the combined demand on the upright and base. Vertical gaps must accommodate the bundle and the lift needed to clear retaining features.
Single-sided storage suits a perimeter position with a working aisle in front. Double-sided rows require access on both faces and a base arrangement rated for the proposed loading pattern.
Indoor storage can protect moisture-sensitive lumber and sheet inventory, while outdoor placement needs a component finish and structural specification suited to the exposure. We establish that distinction before selecting uprights, bases, bracing, and arms. A side-loader carries long material differently from a conventional forklift; the drawing must reflect the actual truck, turning path, load sweep, and approach to every occupied level. The cantilever rack drawing should also identify which load families belong on each face.
Installation is scheduled and managed with experienced crews. Assembly follows the agreed drawing for base positions, upright alignment, bracing, and arm elevations. Your team reviews load identification and capacity information before stocking the row. Later changes to arm height or pack depth should be checked against the specified configuration rather than treated as extra capacity.
Bradenton warehouse racking · Long-load support options · FIFO pallet storage in Bradenton · Bulk pallet lanes in Bradenton
A look at recent pallet rack installations across the Tampa Bay area.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking fitted with wire decking on each level, installed under a wood-truss roof.

Pallet racking set up with carton flow roller lanes on the lower levels.

Drive-in pallet racking built with deep bays that store pallets several positions deep.

Selective pallet racking fitted with wire decking across each level.

Selective pallet racking installed across a warehouse.

Selective pallet racking fitted with wire decking.

Selective pallet racking in a warehouse.

Push back pallet racking with nested carts that store pallets several deep from one aisle.

Selective pallet racking set up along a warehouse wall.
Call (813) 723-3771 with your load list and handling equipment details to discuss the proposed arm arrangement. Call (813) 723-3771.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
(813) 723-3771Monday - Friday: 7:00 AM - 7:00 PM

Every pallet reachable, every time. The baseline we size everything else against.
View details
Two to six pallets deep from one aisle, without giving up much reach.
View details
Load one side, pick the other, and let gravity enforce first in, first out.
View details
Forklifts enter storage lanes, reducing aisle space for large quantities of the same SKU.
View details
Cases advance to the picker instead of the picker hunting for cases.
View detailsOur delivery and installation territory covers Tampa Bay, so one team can handle multiple buildings for the same company.
Located in Tampa, we serve the entire Tampa Bay area with industrial pallet racks and warehouse storage solutions.
7402 N 56th St.
Ste 355-580
Tampa, FL 33617
Monday - Friday: 7:00 AM - 7:00 PM
Saturday: Closed
Sunday: Closed
Call (813) 723-3771 or request a quote and we will get a layout started.